Polymer nanoparticles with a sensitive CO2‐responsive hydrophilic/hydrophobic surface

Poly(methyl methacrylate) (PMMA) nanoparticles with a sensitive CO₂‐responsive hydrophilic/hydrophobic surface that confers controlled dispersion and aggregation in water were prepared by emulsion polymerization at 50 °C under CO₂ bubbling using amphiphilic diblock copolymers of 2‐dimethylaminoethyl methacrylate (DMAEMA) and N‐isopropyl acrylamide (NIPAAm) as an emulsifier. The amphiphilicity of the hydrophobic–hydrophilic diblock copolymer at 50 °C was triggered by CO₂ bubbling in water and enabled the copolymer to serve as an emulsifier. The resulting PMMA nanoparticles were spherical, approximately 100 nm in diameter and exhibited sensitive CO₂/N₂‐responsive dispersion/aggregation in water. Using copolymers with a longer PNIPAAm block length as an emulsifier resulted in smaller particles. A higher concentration of copolymer emulsifier led to particles with a stickier surface. Given its simple preparation and reversible CO₂‐triggered amphiphilic behavior, this newly developed block copolymer emulsifier offers a highly efficient route toward the fabrication of sensitive CO₂‐stimuli responsive polymeric nanoparticle dispersions. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2149–2156     

TBOR-shaped electro-optic modulator with dual output based on double-layer graphene

We proposed an electro-optic modulator with two-bus one-ring (TBOR) structure to improve the extinction ratio and reduce insert loss. It has a dual output compared with one-bus one-ring structure. In addition, double-layer graphene makes it possible for the modulation in the visible to mid-infrared wavelength range. It shows that this new electro-optic modulator can present two switching states well with low insertion loss, high absorption and high extinction ratio. At $\lambda =1550\text{ nm}$, when the switching states are based on the chemical potential, ${\mu }_{\mathrm{c}}=0.38\text{ eV}$ and ${\mu }_{\mathrm{c}}=0.4\text{ eV}$, the insertion losses of both output ports are less than 2 dB, the absorption of the output port coupled via a micro-ring reaches 45 dB and the extinction ratio reaches 14 dB. When the refractive index of the dielectric material is 4.2, the applied voltage will be less than 1.2 V, thus can be used in low-voltage CMOS technology.     

D*-度量空间广义弱压缩映射的不动点定理

介绍了D^*-度量空间中的相关知识, 并基于D^*-度量空间, 将度量空间中与两种距离控制函数(ψ,?)有关的广义弱压缩映射推广到D^*-度量空间, 通过构造迭代序列，讨论了广义弱压缩条件下映射不动点的存在性和唯一性, 给出了几个不动点定理, 所得结果丰富了D^*-度量空间的不动点理论。     

静止轨道星载差分吸收光谱仪CCD成像系统设计

静止轨道卫星差分吸收光谱仪采用摆扫成像方式对大气进行探测,针对其工作时CCD成像系统信噪比大于1 000、高速探测模式下探测周期小于10min、高分辨率模式下探测周期小于1h的要求,进行CCD成像系统设计.选取CCD47-20作为探测器,设计成像电路实现光谱图像信号的采集和上传.分析了帧叠加和像元合并对时间、空间分辨率的影响.结合帧转移CCD的特点设计了每个位置最后一帧读出时摆镜转动的成像方式,并合理设置了帧叠加数和像元合并数,达到优化成像周期的目的.1s曝光时间条件下,该CCD成像系统的高速、高分辨率模式探测周期分别为515s和3 315s,图像信噪比均大于1 000,污染物观测实验中未出现失帧或重复的现象.该CCD成像系统方案满足静止轨道星载差分吸收光谱仪的探测需求,为静止轨道环境监测仪器设计提供参考.     

Real-time phase measurement and correction of dynamic multimode beam using a single spatial light modulator

In this Letter,a novel system for adaptively correcting the phase of a dynamic multimode beam is proposed.While using merely one spatial light modulator,the phase measurement of the first-order diffraction pattern and the correction of the zeroth diffraction order are simultaneously realized.The real-time experimental result is obtained at a control rate of 10 Hz.The power-in-the-bucket value is improved from 38.5%to 61.8%,even with fundamental mode content that is consistently below 30%.To the best of our knowledge,this is the first implementation of real-time adaptive correction of the entire multimode beam.     

双稳态结构中的1/2次谐波共振及其对隔振特性的影响

以典型的双稳态系统——屈曲梁结构为例,基于等效模型,结合解析、数值和实验手段,研究了双稳态结构中的1/2次谐波共振特性、演化过程、参数调节规律及其对隔振特性的影响.研究发现,当非线性刚度系数或激励幅值增加到一定程度时,系统会在一定带宽下产生显著的1/2次谐波共振;随着激励幅值增加,阻尼系统的1/2次谐波遵循“产生-增强-衰退-消失”的过程,该过程对峰值频率和峰值传递率有重要影响;适当提高非线性强度能有效改善双稳态结构隔振特性.针对双稳态屈曲梁结构开展的实验验证了1/2次谐波特性和隔振特性变化规律.     

DFT mechanistic study of the H2‐assisted chain transfer copolymerization of propylene and p‐methylstyrene catalyzed by zirconocene complex

DFT computations have been performed to investigate the mechanism of H₂‐assisted chain transfer strategy to functionalize polypropylene via Zr‐catalyzed copolymerization of propylene and p‐methylstyrene (pMS). The study unveils the following: (i) propylene prefers 1,2‐insertion over 2,1‐insertion both kinetically and thermodynamically, explaining the observed 1,2‐insertion regioselectivity for propylene insertion. (ii) The 2,1‐inserion of pMS is kinetically less favorable but thermodynamically more favorable than 1,2‐insertion. The observation of 2,1‐insertion pMS at the end of polymer chain is due to thermodynamic control and that the barrier difference between the two insertion modes become smaller as the chain length becomes longer. (iii) The pMS insertion results in much higher barriers for subsequent either propylene or pMS insertion, which causes deactivation of the catalytic system. (iv) Small H₂ can react with the deactivated [Zr]?pMS?PP_n facilely, which displace functionalized pMS?PP_n chain and regenerate [Zr]? H active catalyst to continue copolymerization. The effects of counterions are also discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 576–585     

Flame-retardant effect of cross-linked phosphazene derivatives and pentaerythritol derivatives on polypropylene

Journal of Thermal Analysis and Calorimetry - A phosphazene-based flame retardant (PBFA) was synthesized by hexachlorocyclotriphosphazene and N-aminoethylpiperazine. To improve the flame retardancy...     

Structure and Properties of Silumin Surface after Vacuum Arc Plasma-Assisted Deposition of Coatings Irradiated by Low Energy High Current Pulsed Electron Beam

Russian Physics Journal - The paper presents the results of modification of the silumin surface layer using a multicycle processing technique which combines the formation of the film...